Coverage across Renfrewshire and Inverclyde
Booking sensor upgrades and replacement in Renfrewshire and Inverclyde does not depend on being close to a particular town. Engineers working under our management travel throughout the area, and nothing goes ahead until the price has been agreed in writing. Below are the towns we list here, 7 at present, each linking to a page with nearby places and guide prices.
Towns listed in Renfrewshire and Inverclyde: Paisley, Greenock, Renfrew, Johnstone, Erskine, Port Glasgow, Gourock.
What to think about for sensor upgrades and replacement in Renfrewshire and Inverclyde
- Entrances facing busy roads in Renfrewshire and Inverclyde can see false openings from passing vehicles and cyclists. A sensor with direction detection and a tighter zone usually helps.
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in Renfrewshire and Inverclyde so the zones can be set for the new surface.
- Doors with side screens may need a light curtain on the leaf edge or post to protect the gap. This is one of the most common upgrades on older sliding doors.
- Sites in Renfrewshire and Inverclyde that open early or close late may want sensor work done outside trading hours. Tell us the quieter times when you book the visit.
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
Sensor upgrades and replacement in Renfrewshire and Inverclyde: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in Scotland
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance. HSE guidance on those regulations says the frequency of maintenance depends on the equipment and the manufacturer’s information.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in Renfrewshire and Inverclyde and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Get your door detecting people properly again. Contact us about sensor replacement in Renfrewshire and Inverclyde, with the visit cost confirmed before anyone attends.
Sensor upgrades and replacement in Renfrewshire and Inverclyde: questions
Can you upgrade sensors on an old door in Renfrewshire and Inverclyde?
Most older doors can take modern sensors. A few very old controllers cannot monitor current safety sensors. If yours is one of them, we explain whether a controller upgrade or a new drive unit is the better option, and quote it, before any work is done.
What do you charge for sensor upgrades and replacement in Renfrewshire and Inverclyde?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Renfrewshire and Inverclyde, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Can a risk assessment in Renfrewshire and Inverclyde tell us which sensors we need?
Yes. A safety inspection tests each hazard zone and records where sensor coverage is missing or poor. The report then lists the sensors or light curtains needed, and we can quote those items exactly as listed, or you can pass the report to another competent installer.
Our door in Renfrewshire and Inverclyde closes on people. Is that a sensor fault?
It is likely, and the door should be treated as unsafe. Switch it to a safe mode, such as manual or open, and keep people away from the leaves. Tell us it is unsafe and we will give you the earliest visit we can offer, then the engineer will check the safety sensors and their zones.
What should I tell you when reporting a fault in Renfrewshire and Inverclyde?
The address, the type of door, what it is doing or not doing, when the problem started and whether it is safe to use. A photo of the operator label showing the make, and a short video of the fault, help a great deal. With that, we can agree the visit price in writing and send an engineer with the right parts where possible.
Which makes of automatic door can you work on in Renfrewshire and Inverclyde?
Engineers working under our management work on most makes of automatic door, including sliding, swing, folding, telescopic and revolving types. Some older or obsolete operators have limited parts availability. If that applies, we explain the options, which may include a replacement drive unit on the existing frame, and quote them before anything is ordered.
Who is responsible for automatic doors on escape routes in Renfrewshire and Inverclyde?
The person responsible for fire safety under the Fire (Scotland) Act 2005 for those premises. Scottish guidance allows automatic doors on escape routes only where they fail safely to outward opening or have a monitored fail-safe system that opens them on power failure, sensor failure and fire alarm.