Coverage across Aberdeen and Aberdeenshire
There is no branch to visit in Aberdeen and Aberdeenshire; instead, specialist engineers working under our management travel to you. That keeps drive unit replacement available across the whole area, including smaller towns and rural addresses. The page for each of the 7 towns we list below sets out nearby places, guide prices and the questions people usually ask.
Towns listed in Aberdeen and Aberdeenshire: Aberdeen, Peterhead, Inverurie, Fraserburgh, Westhill, Stonehaven, Ellon.
What to think about for drive unit replacement in Aberdeen and Aberdeenshire
- Check the power supply. A dedicated fused spur and isolator near the door is usually needed, and older installations sometimes need electrical work before the new operator goes in.
- If the door is on an escape route, the new drive unit must be set up to open, break out or be openable by hand, as the building's fire strategy requires.
- Listed buildings and conservation areas in Aberdeen and Aberdeenshire make it attractive to keep the existing frame. A new operator inside the existing header changes little that can be seen.
- Heavy glass leaves need an operator rated for their weight. The survey records the size and glass type of each leaf so the right drive unit is specified.
- Battery backup is easier to add with a new drive unit. It lets the door open or close safely in a power cut, which matters most on escape routes.
Drive unit replacement in Aberdeen and Aberdeenshire: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: typically £1,995 to £3,995 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| New drive unit on an existing automatic sliding door | £1,995 – £3,995 | existing leaves kept, installed, ex VAT |
| New operator on an existing automatic swing door | £1,795 – £3,995 | installed, ex VAT |
| Sensors replaced at the same time | £195 – £495 | per sensor, ex VAT |
Standards and rules in Scotland
Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible. BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them.
Whoever motorises a manual door, or builds an automatic door from separate parts, may take on the manufacturer’s legal duties for the finished door: a risk assessment, a technical file kept available for the authorities, a Declaration of Conformity, the conformity marking and instructions. You receive the Declaration of Conformity and the instructions at handover. In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking.
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance.
How it works
- Tell us about the entrance. Send the address, a few photos and a rough size of the opening, and say how the door is used. That is enough for us to suggest options for drive unit replacement and book a survey in Aberdeen and Aberdeenshire.
- Free site survey. A specialist engineer working under our management measures the opening, checks the frame, floor, head height and power, and talks through how people use the entrance. There is no charge and no obligation.
- Fixed written quote. You receive a fixed, itemised written quote with the specification, lead time, payment stages and warranty terms. The price does not change unless the scope does, and any change is agreed in writing first.
- Installation and handover. The door is fitted on the agreed dates, then set up, tested and documented with reference to BS EN 16005. You are shown the controls and the simple checks to make, and receive the handover paperwork.
Book a free survey in Aberdeen and Aberdeenshire to find out whether a new drive unit will bring your automatic door back to reliable use. The quote is fixed and itemised.
Drive unit replacement in Aberdeen and Aberdeenshire: questions
What if the frame of our door in Aberdeen and Aberdeenshire is not worth keeping?
Then we will tell you. Damaged or corroded frames, glass that is not safety glass, or an opening that is too narrow for the people using it are all reasons to choose a new door instead. We can quote both options so you can compare them side by side.
How are prices worked out for drive unit replacement in Aberdeen and Aberdeenshire?
Our guide is £1,995 to £3,995 excluding VAT (per door), the same guide prices we use across the UK. The free site survey in Aberdeen and Aberdeenshire confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
Do you replace automatic door drive units in Aberdeen and Aberdeenshire?
Yes. We are the contracting party for drive unit replacements in Aberdeen and Aberdeenshire, and the survey and changeover are carried out by specialist engineers we manage. The survey is free and checks that the frame and leaves are worth keeping. You then receive a fixed, itemised quote for the new operator, sensors and any other parts the door needs.
Do you provide paperwork for the converted door in Aberdeen and Aberdeenshire?
Yes. When we fit a new drive unit we prepare the paperwork for the finished door, including the risk assessment, Declaration of Conformity and user instructions, and hand it over with the test results and settings. It belongs with your building records.
Can automatic doors be fitted to a listed building in Aberdeen and Aberdeenshire?
Often, yes, but listed building consent is normally needed for changes that affect the character of the building, inside or out. Slim operators, concealed fixings and automating the existing door can all reduce the visual impact. Speak to the conservation officer at the local planning authority early; we can provide drawings and specifications to help.
What happens once the installation in Aberdeen and Aberdeenshire is finished?
The engineer tests every function, including the safety sensors and the behaviour on power loss, and sets the door up with reference to BS EN 16005. You are shown how to use the controls and which simple checks to make, and you receive the handover documents, including the test record and any conformity paperwork that applies to the work.
Do businesses in Aberdeen and Aberdeenshire have to fit automatic doors?
No law requires automatic doors everywhere. Under the Equality Act 2010 service providers and employers must make reasonable adjustments for disabled people, and Scottish guidance says powered doors improve accessibility at entrances. An automatic door is often the practical answer.