Coverage across Lancashire
Not every part of Lancashire is easy to reach, and some sites need planning around access, parking or opening hours. We take that into account when arranging frameless glass automatic doors, and the engineer, working under our management, arrives with what the job is likely to need. The towns below, 21 in all, each have their own page, but any address in the area can be covered.
Towns listed in Lancashire: Preston, Burnley, Blackburn, Blackpool, Morecambe, Lancaster, Lytham St Annes, Skelmersdale, Bamber Bridge, Leyland, Accrington, Chorley, Darwen, Thornton-Cleveleys, Nelson, Fleetwood, Ormskirk, Rawtenstall, Colne, Poulton-le-Fylde, Heysham.
What to think about for frameless glass automatic doors in Lancashire
- The header needs a rigid fixing. In modern offices in Lancashire with suspended ceilings, the operator is usually fixed to the slab above with a steel support, which the survey designs in from the start.
- Street-facing doors in Lancashire that take the full force of wind and rain may be better as framed sliding doors. Frameless leaves have small gaps that let draughts and noise through.
- Floor guides need a sound floor. Where the entrance has stone, tiles or polished concrete, agree whether a channel will be cut or a small surface guide fixed, and who makes good the finish.
- Hotels and restaurants in Lancashire often want the door to stay open on warm days and close in bad weather. A programme switch with hold-open and automatic modes makes that a simple daily choice.
- Clear glass is easy to walk into. Plan manifestation at the outset, whether frosted bands or a pattern based on your logo, rather than adding stickers after the door is fitted.
Frameless glass automatic doors in Lancashire: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: from £5,495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Single-slide frameless glass door | £5,495 – £8,995 | installed, ex VAT |
| Bi-parting frameless glass door, about 2 m clear opening | £7,495 – £12,995 | installed, ex VAT |
| Touch-free switch or push pad, fitted | £145 – £395 | per switch, ex VAT |
| Card or fob reader tied into the door | £795 – £2,495 | per door, ex VAT |
| Battery backup for power-cut operation | £395 – £695 | per door, ex VAT |
Standards and rules in England
Building regulations guidance in England (Approved Document M, Volume 2) says a powered opening system should be used where a self-closing entrance door would need more than 30 N at the leading edge to open, or more than 22.5 N between 30° and 60°, and expects external doors used by the public in new buildings to give at least 1000 mm of effective clear width.
In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking. Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance.
Under the Equality Act 2010, service providers and employers must make reasonable adjustments for disabled people, which can include altering a physical feature such as a heavy entrance door. New entrances and some alterations count as building work, so check with building control before the work is ordered.
How it works
- Start with a short enquiry. Use the form, phone or email. Tell us whether the work is a new door, an upgrade or an opener for a home, and we arrange the next step for your site in Lancashire.
- Measured survey. The free survey confirms what will fit and what the entrance needs: opening width, door type, activation, safety sensors and behaviour on power loss or fire alarm, matched to how the building is used.
- Written price, no surprises. A fixed, itemised quote sets out the specification, the work involved, the expected lead time and the warranty terms. You can ask questions or change the specification before accepting it.
- Installed and commissioned. The door is installed with as little disruption as possible, then set up and tested for its hazard zones. Before leaving, the engineer explains the controls and hands over the documents for your records.
Planning an office fit-out in Lancashire? Share your partition drawings and we will quote for frameless glass automatic doors to match, with a fixed, itemised price.
Frameless glass automatic doors in Lancashire: questions
What should we do if the frameless door in Lancashire is damaged?
If the glass is chipped or cracked, switch the door off, keep people away from the damaged leaf and contact us. A repair or replacement visit is priced in writing before an engineer attends, and replacement glass is quoted before it is ordered. Laminated glass usually stays in place until it can be replaced.
Can you give me a price for frameless glass automatic doors in Lancashire?
Our guide starts from £5,495 excluding VAT (per door set), the same guide price we use across the UK. The free site survey in Lancashire confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
Is the survey for a frameless door in Lancashire free?
Yes. For a new frameless automatic door, the survey is free and you are under no obligation. The engineer measures the opening, checks the structure above and the floor below, discusses glass and fittings, and you then receive a drawing and a fixed, itemised written quote.
How long does fitting take in Lancashire?
Most frameless automatic doors take a day on site once the glass has been made, which is typically 4 to 8 weeks from order. Work in occupied offices can be planned for quieter times, early mornings or weekends, and any extra cost for out-of-hours work is shown separately in the quote.
Can automatic doors be fitted to a listed building in Lancashire?
Often, yes, but listed building consent is normally needed for changes that affect the character of the building, inside or out. Slim operators, concealed fixings and automating the existing door can all reduce the visual impact. Speak to the conservation officer at the local planning authority early; we can provide drawings and specifications to help.
What happens once the installation in Lancashire is finished?
The engineer tests every function, including the safety sensors and the behaviour on power loss, and sets the door up with reference to BS EN 16005. You are shown how to use the controls and which simple checks to make, and you receive the handover documents, including the test record and any conformity paperwork that applies to the work.
Which building regulations apply to a new automatic entrance in Lancashire?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.