Coverage across West Yorkshire
There is no branch to visit in West Yorkshire; instead, specialist engineers working under our management travel to you. That keeps frameless glass automatic doors available across the whole area, including smaller towns and rural addresses. The page for each of the 26 towns we list below sets out nearby places, guide prices and the questions people usually ask.
Towns listed in West Yorkshire: Leeds, Bradford, Huddersfield, Wakefield, Halifax, Dewsbury, Morley, Keighley, Castleford, Pontefract, Batley, Yeadon, Brighouse, Shipley, Cleckheaton, Pudsey, Ossett, Normanton, Guiseley, Rothwell, Liversedge, Horsforth, South Elmsall, Mirfield, Heckmondwike, Bingley.
What to think about for frameless glass automatic doors in West Yorkshire
- Cleaning staff at busy venues in West Yorkshire should use non-abrasive products on frameless doors, keep the floor guide clear of grit and report any chipped glass edge straight away.
- The header needs a rigid fixing. In modern offices in West Yorkshire with suspended ceilings, the operator is usually fixed to the slab above with a steel support, which the survey designs in from the start.
- Listed interiors and heritage buildings in West Yorkshire sometimes favour frameless glass because it hides less of the original fabric. Consent may still be needed, so check with the planning authority early.
- Floor guides need a sound floor. Where the entrance has stone, tiles or polished concrete, agree whether a channel will be cut or a small surface guide fixed, and who makes good the finish.
- Showrooms in West Yorkshire with large displays, or vehicles moving in and out, may want a wide bi-parting frameless door with a hold-open mode for deliveries.
Frameless glass automatic doors in West Yorkshire: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: from £5,495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Single-slide frameless glass door | £5,495 – £8,995 | installed, ex VAT |
| Bi-parting frameless glass door, about 2 m clear opening | £7,495 – £12,995 | installed, ex VAT |
| Touch-free switch or push pad, fitted | £145 – £395 | per switch, ex VAT |
| Card or fob reader tied into the door | £795 – £2,495 | per door, ex VAT |
| Battery backup for power-cut operation | £395 – £695 | per door, ex VAT |
Standards and rules in England
Building regulations guidance in England (Approved Document M, Volume 2) says a powered opening system should be used where a self-closing entrance door would need more than 30 N at the leading edge to open, or more than 22.5 N between 30° and 60°, and expects external doors used by the public in new buildings to give at least 1000 mm of effective clear width.
In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking. Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance.
Under the Equality Act 2010, service providers and employers must make reasonable adjustments for disabled people, which can include altering a physical feature such as a heavy entrance door. New entrances and some alterations count as building work, so check with building control before the work is ordered.
How it works
- Send photos and the address. A few pictures of the door from both sides, the address in West Yorkshire and a note of who uses the entrance help us understand the job before anyone visits the site.
- No-cost survey on site. We arrange a survey at a time that suits the building. The engineer records measurements, fixings and power, plus any constraints such as listed status, opening hours or access for deliveries.
- Itemised quote to approve. We price every element of the work on frameless glass automatic doors separately in a written quote that you can check, share and approve. Lead time and payment stages are stated, and nothing is ordered until you accept.
- Fit, test and hand over. On the agreed dates the engineer installs the equipment, commissions the operator and tests each safety function. You get a demonstration, the test record and any conformity paperwork that applies to the work.
Use the guide price tool for an early figure, then let us survey your showroom, studio or reception in West Yorkshire.
Frameless glass automatic doors in West Yorkshire: questions
What should we do if the frameless door in West Yorkshire is damaged?
If the glass is chipped or cracked, switch the door off, keep people away from the damaged leaf and contact us. A repair or replacement visit is priced in writing before an engineer attends, and replacement glass is quoted before it is ordered. Laminated glass usually stays in place until it can be replaced.
How are prices worked out for frameless glass automatic doors in West Yorkshire?
Our guide starts from £5,495 excluding VAT (per door set), the same guide price we use across the UK. The free site survey in West Yorkshire confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
Is the survey for a frameless door in West Yorkshire free?
Yes. For a new frameless automatic door, the survey is free and you are under no obligation. The engineer measures the opening, checks the structure above and the floor below, discusses glass and fittings, and you then receive a drawing and a fixed, itemised written quote.
How long does fitting take in West Yorkshire?
Most frameless automatic doors take a day on site once the glass has been made, which is typically 4 to 8 weeks from order. Work in occupied offices can be planned for quieter times, early mornings or weekends, and any extra cost for out-of-hours work is shown separately in the quote.
How much disruption should we expect while the work is done in West Yorkshire?
Most installations take one visit or a short series of visits, with dust and noise kept to the area around the door. The engineer screens off the work area, keeps a route in or out where possible and clears up before leaving. Larger entrances, lobbies or structural changes take longer, and the quote explains how that work is phased.
Can automatic doors be fitted to a listed building in West Yorkshire?
Often, yes, but listed building consent is normally needed for changes that affect the character of the building, inside or out. Slim operators, concealed fixings and automating the existing door can all reduce the visual impact. Speak to the conservation officer at the local planning authority early; we can provide drawings and specifications to help.
Which building regulations apply to a new automatic entrance in West Yorkshire?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.