Coverage across Gwent
Our coverage of Gwent is not tied to a depot or a showroom. Engineers who carry out automatic door refurbishment for us travel to each site, so a farm shop down a country lane goes through the same process as a city-centre office. Every job is priced in writing before work starts, and the town list below currently numbers 14.
Towns listed in Gwent: Newport, Cwmbran, Pontypool, Ebbw Vale, Caerphilly, Blackwood, Tredegar, Abergavenny, Bargoed, Chepstow, Risca, Abertillery, Monmouth, Caldicot.
What to think about for automatic door refurbishment in Gwent
- After refurbishment, sensors and speeds are reset to suit the new parts. Keep the test record with your service history so later engineers can see what was done.
- Care settings in Gwent benefit from level thresholds and smooth-running leaves that do not snag walking frames, trolleys or wheelchair footplates as people pass through.
- If the operator is close to the end of its life, refurbishing the running gear while fitting a new drive unit saves a second visit and a second set-up.
- Office blocks and business parks in Gwent with several matching doors can refurbish them together for a consistent finish and a lower cost per door.
- Older shopfronts with discontinued door systems may need equivalent parts rather than exact matches. The survey identifies what is still available before anything is ordered.
Automatic door refurbishment in Gwent: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: from £395 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Running gear refresh: rollers, guides, brushes and seals | £395 – £895 | per door, ex VAT |
| Track overhaul | £395 – £895 | per door, ex VAT |
| Replacement glass leaf | from £495 | each, ex VAT; size and glass type on survey |
| Full refurbishment of a sliding door | £1,495 – £2,995 | running gear, seals, guides and one leaf, ex VAT |
Standards and rules in Wales
Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible. BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them.
Whoever motorises a manual door, or builds an automatic door from separate parts, may take on the manufacturer’s legal duties for the finished door: a risk assessment, a technical file kept available for the authorities, a Declaration of Conformity, the conformity marking and instructions. You receive the Declaration of Conformity and the instructions at handover. In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking.
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance.
How it works
- Send photos and the address. A few pictures of the door from both sides, the address in Gwent and a note of who uses the entrance help us understand the job before anyone visits the site.
- No-cost survey on site. We arrange a survey at a time that suits the building. The engineer records measurements, fixings and power, plus any constraints such as listed status, opening hours or access for deliveries.
- Itemised quote to approve. We price every element of the work on automatic door refurbishment separately in a written quote that you can check, share and approve. Lead time and payment stages are stated, and nothing is ordered until you accept.
- Fit, test and hand over. On the agreed dates the engineer installs the equipment, commissions the operator and tests each safety function. You get a demonstration, the test record and any conformity paperwork that applies to the work.
Send us photos of the door that needs attention in Gwent, and we will arrange a survey at no cost and an itemised quote for the work.
Automatic door refurbishment in Gwent: questions
Can you replace a single broken glass leaf in Gwent?
Yes. The leaf is made safe, measured and reglazed with new safety glass, or replaced completely if its frame is damaged. New glass is typically 2 to 4 weeks from order. Once the leaf is rehung, the door is set up again and the track and floor guide are checked.
What is the guide price for automatic door refurbishment in Gwent?
Our guide starts from £395 excluding VAT (per door), the same guide price we use across the UK. The free site survey in Gwent confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
Is it worth refurbishing an old door at our premises in Gwent?
If the frame is sound and the opening size still works, usually yes, as refurbishment costs far less than a new door. If the frame is corroded, the glass is not safety glass or the opening is too narrow, a new door may be better value, and the survey tells you which.
Can you refinish the frame of our door in Gwent?
Yes. Aluminium frames can be cleaned, repaired and recoated on site to refresh their colour. Badly damaged sections may need replacing rather than refinishing. Refinishing is listed separately in the quote, so you can decide whether to include it now or leave it for a later phase.
Can automatic doors be fitted to a listed building in Gwent?
Often, yes, but listed building consent is normally needed for changes that affect the character of the building, inside or out. Slim operators, concealed fixings and automating the existing door can all reduce the visual impact. Speak to the conservation officer at the local planning authority early; we can provide drawings and specifications to help.
What happens to the old door when a new one is fitted in Gwent?
If the work replaces an existing door, frame or operator, removal and disposal are listed in the quote. The old door comes out only when the new one is ready to go in, so the opening is not left empty for longer than necessary. Making good to the surrounding wall, floor or ceiling is included where the quote says so.
Who is responsible for automatic doors on escape routes in Gwent?
The responsible person under the Regulatory Reform (Fire Safety) Order 2005. Automatic doors on an escape route need fail-safe opening or break-out, and sliding or revolving doors must not be used for exits specifically intended as emergency exits.