Covering Wellington and nearby
Homes, businesses and public buildings throughout the TF1 postcode district can arrange sensor upgrades and replacement with us. We are the contracting party and organise every visit; the engineer, who works under our management, travels in to Wellington for the job rather than working from premises in town.
Small offices, community centres and village halls around Wellington tend to have one main entrance, often used by visitors who need level access without steps. Automating the existing door, rather than replacing it, is frequently the most practical and affordable route.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Telford (3.3 miles), Shrewsbury (9.9 miles), Stafford (18.3 miles), Wolverhampton (18.3 miles), Wednesfield (19.5 miles), Sedgley (19.8 miles).
What to think about for sensor upgrades and replacement in Wellington
- Entrances facing busy roads in Wellington can see false openings from passing vehicles and cyclists. A sensor with direction detection and a tighter zone usually helps.
- After a near miss at a door in Wellington, keep a note of what happened and where the person was standing. It helps the engineer judge which zone the sensor failed to cover.
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in Wellington so the zones can be set for the new surface.
- Swing doors in narrow corridors need sensors on the leaf to protect people on both sides. The engineer checks the swing path and any walls or fittings close by.
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
Sensor upgrades and replacement in Wellington: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Make contact. Phone, email or use the form. Tell us the type of door, what it is doing and whether it is safe to use, so the right visit for sensor upgrades and replacement can be planned.
- Written visit price. The cost of attending is agreed in writing before the visit is booked. For a planned service or inspection, the price per door and what each visit includes are set out at the same time.
- On-site work. The engineer, working under our management, checks the door from end to end, deals with the fault or the service, and tests every safety function and sensor setting before signing the door off.
- Report and quote. You receive a report of the findings. Where a repair, part or upgrade is recommended, it is quoted in writing so you can decide, and the door is left in a safe state if it cannot be used.
Get your door detecting people properly again. Contact us about sensor replacement in Wellington, with the visit cost confirmed before anyone attends.
Sensor upgrades and replacement in Wellington: questions
Can a risk assessment in Wellington tell us which sensors we need?
Yes. A safety inspection tests each hazard zone and records where sensor coverage is missing or poor. The report then lists the sensors or light curtains needed, and we can quote those items exactly as listed, or you can pass the report to another competent installer.
What price range should I expect for sensor upgrades and replacement in Wellington?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Wellington, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Our door in Wellington closes on people. Is that a sensor fault?
It is likely, and the door should be treated as unsafe. Switch it to a safe mode, such as manual or open, and keep people away from the leaves. Tell us it is unsafe and we will give you the earliest visit we can offer, then the engineer will check the safety sensors and their zones.
Will new sensors stop false openings at our entrance in Wellington?
Usually. Modern sensors can ignore cross traffic and detect only people moving towards the door, and the zone can be narrowed. If the entrance faces a busy street or catches heavy weather, the engineer may suggest a sensor that filters those conditions better.
Can you take over servicing of doors in Wellington from another company?
Yes. Send us the door details and, if you have them, previous service records or inspection reports. The first visit gives a baseline for each door, and its price is agreed in writing beforehand. From then on, records continue in one consistent format, whichever company looked after the doors before.
Are parts quoted before they are fitted?
Always. If a repair or service in Wellington needs parts, such as rollers, belts, sensors, a control board or a motor, we quote them in writing first. Some common parts may be on the engineer's van; others are ordered once you accept the quote and fitted on a return visit at a price already agreed.
Who is responsible for automatic doors on escape routes in Wellington?
Under the Regulatory Reform (Fire Safety) Order 2005 the responsible person for the premises must make sure escape routes work and fire safety equipment is maintained. Automatic doors on an escape route need fail-safe opening or break-out, set by the fire strategy.