Covering Andover and nearby
Coverage for sensor upgrades and replacement runs across the SP10 postcode district and out into the surrounding parts of Hampshire. Wherever the building is, the arrangements stay the same: one contracting party, a written price before work, and a specialist engineer working under our management on site.
Many buildings in Andover are older, with timber frames, thick walls, steps or uneven thresholds. These affect where an operator and sensors can go, and the engineer checks them on site before anything is fitted or adjusted.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Winchester (12.6 miles), Newbury (15.0 miles), Romsey (15.4 miles), Chandler's Ford (16.2 miles), Salisbury (16.4 miles), Thatcham (16.7 miles).
What to think about for sensor upgrades and replacement in Andover
- Sensor changes on escape route doors must never stop the door opening when it needs to. The engineer checks the door's escape mode after any sensor work.
- Care settings in Andover often need longer hold-open times and wider safety zones for residents who move slowly, use walking frames or pause in the doorway.
- Sites in Andover that open early or close late may want sensor work done outside trading hours. Tell us the quieter times when you book the visit.
- Doors with side screens may need a light curtain on the leaf edge or post to protect the gap. This is one of the most common upgrades on older sliding doors.
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
Sensor upgrades and replacement in Andover: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in Andover and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Ask for a price on new safety or activation sensors in Andover. Each one is set up for the door's hazard zones and tested before the engineer leaves.
Sensor upgrades and replacement in Andover: questions
Can you upgrade sensors on an old door in Andover?
Most older doors can take modern sensors. A few very old controllers cannot monitor current safety sensors. If yours is one of them, we explain whether a controller upgrade or a new drive unit is the better option, and quote it, before any work is done.
What do you charge for sensor upgrades and replacement in Andover?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Andover, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Can you price new sensors for my door in Andover from photos?
Often, yes. Photos of the sensor, the door from both sides and the label on the operator cover usually tell us which sensor is needed and whether it suits the controller. We can then quote the sensor and fitting in advance, with the visit price confirmed before anyone travels.
Will you record the sensor settings for our building in Andover?
Yes. The job report lists each sensor fitted, its position, the settings used and the test results. Keep it with your service records, as it helps future engineers and shows the door's safety set-up was checked after the work. The same details are useful if an insurer or inspector asks.
Can you take over servicing of doors in Andover from another company?
Yes. Send us the door details and, if you have them, previous service records or inspection reports. The first visit gives a baseline for each door, and its price is agreed in writing beforehand. From then on, records continue in one consistent format, whichever company looked after the doors before.
Are parts quoted before they are fitted?
Always. If a repair or service in Andover needs parts, such as rollers, belts, sensors, a control board or a motor, we quote them in writing first. Some common parts may be on the engineer's van; others are ordered once you accept the quote and fitted on a return visit at a price already agreed.
Which building regulations apply to a new automatic entrance in Andover?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.