Covering Andover and nearby
Our coverage of Andover takes in the SP10 postcode district and the neighbouring parts of Hampshire. If your address sits close to a boundary, it is still covered: send the postcode with your enquiry about safety inspections and risk assessments and we will confirm the arrangements and the price in writing.
Independent businesses in Andover often have one entrance and cannot close for long. Work is usually scheduled early, late or on a quiet day, and where a door must be out of use for a period, we plan to keep the entrance usable or secure.
Nearby towns we also list for safety inspections and risk assessments (straight-line distance): Winchester (12.6 miles), Newbury (15.0 miles), Romsey (15.4 miles), Chandler's Ford (16.2 miles), Salisbury (16.4 miles), Thatcham (16.7 miles).
What to think about for safety inspections and risk assessments in Andover
- Older shopfronts and listed buildings in Andover may have narrow side screens and tight gaps that were thought acceptable when fitted. The report weighs what can reasonably be improved.
- Glass leaves need safety glazing and visible markings. Faded or missing manifestation is a common finding, and one of the quickest and cheapest to put right.
- Power failure behaviour is easy to overlook. The inspection tests what the door does when the mains supply or battery fails, which matters most on escape routes.
- Care homes and hospitals in Andover have users who move slowly or unpredictably. The inspection pays close attention to sensor coverage and door speeds where frail or confused people pass through.
- Retail entrances in Andover with heavy footfall can have sensors knocked out of alignment over time. The inspection checks that detection still covers the full closing edge.
Safety inspections and risk assessments in Andover: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £125 to £250 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Safety inspection and risk assessment, existing door | £125 – £250 | per door, written report, ex VAT |
| Inspection added to a service visit | reduced | quoted with the service |
| Upgrades found by the inspection | quoted separately | see safety and compliance upgrades |
The inspection price is agreed in writing before the visit. Any upgrades the report recommends are quoted separately so you can plan them.
Standards and rules in England
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance. HSE guidance on those regulations says the frequency of maintenance depends on the equipment and the manufacturer’s information.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in Andover and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Ask for an inspection price for your site in Andover. Every door is assessed on its hazard zones, and upgrades are quoted separately if you want them.
Safety inspections and risk assessments in Andover: questions
How long will our door in Andover be out of use during the inspection?
Usually only for short periods while sensors are tested and the door is observed in different modes. A single door generally takes about an hour in total. For busy entrances the inspection can be planned for a quieter time, or one leaf tested at a time where the door allows it.
What will safety inspections and risk assessments in Andover cost?
Our guide is £125 to £250 excluding VAT (per door), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Andover, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Our insurer in Andover has asked for a risk assessment. Is this what they mean?
Most likely. Insurers usually want a documented, site-specific risk assessment of the door by a competent person, along with service records. Check their exact wording and send it to us. Our report covers the door's hazard zones, test results and recommended actions, which is what most insurers expect to see.
Can an inspection in Andover be combined with a service?
Yes, and it often makes sense. The engineer services the door, then carries out the risk assessment while on site, which saves a second visit. The combined price is agreed in writing before the visit, and you receive both the service record and the inspection report.
How is the visit price set for work in Andover?
We agree the visit price with you in writing before an engineer attends. It is based on the type of door, the work requested and the location. If parts or further work are needed once the engineer has found the cause, those are quoted before they are done, so the cost never moves without your agreement.
What happens during a visit in Andover?
The engineer checks how the door is operating, diagnoses the fault or carries out the service, and tests the safety sensors and other functions before leaving. On a service visit that includes cleaning, adjustment and lubrication where needed. Anything that cannot be put right on the visit, or that needs parts, is explained and quoted before further work goes ahead.
Which building regulations apply to a new automatic entrance in Andover?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.