Covering Crewe and nearby
For sensor upgrades and replacement, coverage around Crewe is set by postcode and includes the CW1 and CW2 postcode districts, as well as nearby addresses in Cheshire. Specialist engineers working under our management attend each site, and the price is agreed in writing beforehand.
Business parks around Crewe tend to have reception doors that see steady rather than heavy traffic, often with access control after hours. A swing or sliding operator linked to a card reader or intercom is a common arrangement for entrances like these.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Nantwich (3.8 miles), Sandbach (4.6 miles), Winsford (7.3 miles), Kidsgrove (8.5 miles), Congleton (10.5 miles), Newcastle-under-Lyme (11.0 miles).
What to think about for sensor upgrades and replacement in Crewe
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
- If several doors at one site have the same old sensor, replacing them together keeps the doors behaving consistently and may reduce the cost per sensor.
- Swing doors in narrow corridors need sensors on the leaf to protect people on both sides. The engineer checks the swing path and any walls or fittings close by.
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in Crewe so the zones can be set for the new surface.
- Rain, snow and blowing leaves can trigger radar sensors over exposed doors. Some sensors filter weather better than others, which the engineer weighs up when choosing a replacement.
Sensor upgrades and replacement in Crewe: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance. HSE guidance on those regulations says the frequency of maintenance depends on the equipment and the manufacturer’s information.
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in Crewe and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Ask for a price on new safety or activation sensors in Crewe. Each one is set up for the door's hazard zones and tested before the engineer leaves.
Sensor upgrades and replacement in Crewe: questions
Our door in Crewe closes on people. Is that a sensor fault?
It is likely, and the door should be treated as unsafe. Switch it to a safe mode, such as manual or open, and keep people away from the leaves. Tell us it is unsafe and we will give you the earliest visit we can offer, then the engineer will check the safety sensors and their zones.
How are prices worked out for sensor upgrades and replacement in Crewe?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Crewe, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Do you replace automatic door sensors in Crewe?
Yes. Sensor replacement and upgrades in Crewe are booked and managed by us and carried out by engineers who specialise in automatic doors. They work on sensors for sliding, swing, folding and revolving doors from most makers. The visit cost is set in writing before they attend, and each new sensor is tested before they leave.
Can you upgrade sensors on an old door in Crewe?
Most older doors can take modern sensors. A few very old controllers cannot monitor current safety sensors. If yours is one of them, we explain whether a controller upgrade or a new drive unit is the better option, and quote it, before any work is done.
What happens during a visit in Crewe?
The engineer checks how the door is operating, diagnoses the fault or carries out the service, and tests the safety sensors and other functions before leaving. On a service visit that includes cleaning, adjustment and lubrication where needed. Anything that cannot be put right on the visit, or that needs parts, is explained and quoted before further work goes ahead.
Do you offer service contracts in Crewe?
Yes. A service contract sets out how many visits a year each door receives, what each visit includes and the price, all agreed in writing before you sign. Contracts suit sites with several doors or busy entrances, because visits are planned ahead and the records stay in one place. Contract length and notice terms are shown in the agreement.
Who is responsible for automatic doors on escape routes in Crewe?
Under the Regulatory Reform (Fire Safety) Order 2005 the responsible person for the premises must make sure escape routes work and fire safety equipment is maintained. Automatic doors on an escape route need fail-safe opening or break-out, set by the fire strategy.