Coverage across Kent
There is no branch to visit in Kent; instead, specialist engineers working under our management travel to you. That keeps accessible door operators available across the whole area, including smaller towns and rural addresses. The page for each of the 24 towns we list below sets out nearby places, guide prices and the questions people usually ask.
Towns listed in Kent: Maidstone, Gillingham, Chatham, Tunbridge Wells, Folkestone, Margate, Ashford, Canterbury, Sittingbourne, Gravesend, Dartford, Ramsgate, Dover, Tonbridge, Strood, Whitstable, Deal, Sevenoaks, Rochester, Herne Bay, Northfleet, Broadstairs, Faversham, Swanley.
What to think about for accessible door operators in Kent
- Power is usually taken from a fused spur near the head of the door. If there is no supply close by, allow for an electrician to run one, ideally hidden in trunking or the wall.
- Accessible toilets need a pad inside and out, a lock button that disables the outside pad while the room is in use, and a way for staff to open the door in an emergency.
- Glazed doors in shop fronts and offices in Kent need visible push pads and clear markings on the glass, so people with sight loss can find the pad and see where the door is.
- Place push pads where a wheelchair user can reach them without the door swinging into them. That often means mounting a pad on a post or a side wall rather than on the frame.
- If the door is a fire door, find its rating or records before the survey. Fixings and cabling must respect the rating, and the operator must release the door on the fire alarm.
Accessible door operators in Kent: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: typically £1,795 to £2,995 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Low-energy operator on an existing single door, with push pads | £1,795 – £2,995 | installed, ex VAT |
| Operators on an existing pair of doors | £3,795 – £6,495 | installed, ex VAT |
| Touch-free switch or push pad, fitted | £145 – £395 | per switch, ex VAT |
| Radio push-button kit | £195 – £495 | buttons and receiver, ex VAT |
| Card or fob reader tied into the door | £795 – £2,495 | per door, ex VAT |
Standards and rules in England
Under the Equality Act 2010, service providers and employers must make reasonable adjustments for disabled people, which can include altering a physical feature such as a heavy entrance door. Fitting an automatic door helps, but does not on its own guarantee those duties are met.
Building regulations guidance in England (Approved Document M, Volume 2) says a powered opening system should be used where a self-closing entrance door would need more than 30 N at the leading edge to open, or more than 22.5 N between 30° and 60°, and expects external doors used by the public in new buildings to give at least 1000 mm of effective clear width.
Whoever motorises a manual door, or builds an automatic door from separate parts, may take on the manufacturer’s legal duties for the finished door: a risk assessment, a technical file kept available for the authorities, a Declaration of Conformity, the conformity marking and instructions. You receive the Declaration of Conformity and the instructions at handover. In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking.
How it works
- Send photos and the address. A few pictures of the door from both sides, the address in Kent and a note of who uses the entrance help us understand the job before anyone visits the site.
- No-cost survey on site. We arrange a survey at a time that suits the building. The engineer records measurements, fixings and power, plus any constraints such as listed status, opening hours or access for deliveries.
- Itemised quote to approve. We price every element of the work on accessible door operators separately in a written quote that you can check, share and approve. Lead time and payment stages are stated, and nothing is ordered until you accept.
- Fit, test and hand over. On the agreed dates the engineer installs the equipment, commissions the operator and tests each safety function. You get a demonstration, the test record and any conformity paperwork that applies to the work.
From one toilet door to a whole accessible route, ask for a fixed price for accessible door operators in Kent. The survey is free.
Accessible door operators in Kent: questions
Can the operator be serviced after installation in Kent?
Yes. We can arrange visits where the speed, force, safety settings, push pads and closer are checked and a written record is left. You agree the cost of each visit in writing beforehand, and how often we come depends on how much the door is used.
What will accessible door operators in Kent cost?
Our guide is £1,795 to £2,995 excluding VAT (per single door), the same guide prices we use across the UK. The free site survey in Kent confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
How soon can an operator be fitted at our premises in Kent?
Lead time is typically 2 to 4 weeks from accepting the quote, depending on the operator and any parts the door needs. We give the expected lead time in writing with the quote, and agree the fitting date with you once the parts are ready.
Who will fit the operator at our building in Kent?
The engineer will be a specialist working under our management. We are the contracting party, so the quote, the warranty terms and any follow-up all come through us. Before handover, the door is set up, tested and documented with reference to BS EN 16005.
What power supply is needed for accessible door operators in Kent?
Most powered doors need a fused spur close to the operator, and some activation and access control devices also need a low-voltage link. The survey checks what is already there. If a new supply is required, the quote says whether we arrange it or your own electrician does, so nothing is left unclear on the day.
Do you service doors in Kent after installing them?
Yes. We recommend a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer's instructions and how heavily the door is used; busy doors are often serviced more often. Servicing can follow on from the installation, with the price agreed in writing and a record left after every visit.
Do businesses in Kent have to fit automatic doors?
No law says every building must have automatic doors. Under the Equality Act 2010, service providers and employers must make reasonable adjustments for disabled people, and building regulations guidance in England calls for a powered door where an entrance door would otherwise be too heavy to open. An automatic door is often the simplest way to meet both.