Covering Consett and nearby
Homes, businesses and public buildings throughout the DH8 postcode district can arrange sensor upgrades and replacement with us. We are the contracting party and organise every visit; the engineer, who works under our management, travels in to Consett for the job rather than working from premises in town.
GP surgeries, dental practices and pharmacies in Consett often serve older patients and people with limited mobility. A low-energy swing operator, or a gentle sliding door with a push pad, can make a real difference at entrances like these.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Stanley (5.4 miles), Chester-le-Street (10.2 miles), Durham (11.5 miles), Gateshead (11.8 miles), Newcastle upon Tyne (11.9 miles), Washington (12.9 miles).
What to think about for sensor upgrades and replacement in Consett
- Rain, snow and blowing leaves can trigger radar sensors over exposed doors. Some sensors filter weather better than others, which the engineer weighs up when choosing a replacement.
- Entrances facing busy roads in Consett can see false openings from passing vehicles and cyclists. A sensor with direction detection and a tighter zone usually helps.
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in Consett so the zones can be set for the new surface.
- After a near miss at a door in Consett, keep a note of what happened and where the person was standing. It helps the engineer judge which zone the sensor failed to cover.
- Sensor changes on escape route doors must never stop the door opening when it needs to. The engineer checks the door's escape mode after any sensor work.
Sensor upgrades and replacement in Consett: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in Consett and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Get your door detecting people properly again. Contact us about sensor replacement in Consett, with the visit cost confirmed before anyone attends.
Sensor upgrades and replacement in Consett: questions
Will you record the sensor settings for our building in Consett?
Yes. The job report lists each sensor fitted, its position, the settings used and the test results. Keep it with your service records, as it helps future engineers and shows the door's safety set-up was checked after the work. The same details are useful if an insurer or inspector asks.
Can you give me a price for sensor upgrades and replacement in Consett?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Consett, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Our door in Consett closes on people. Is that a sensor fault?
It is likely, and the door should be treated as unsafe. Switch it to a safe mode, such as manual or open, and keep people away from the leaves. Tell us it is unsafe and we will give you the earliest visit we can offer, then the engineer will check the safety sensors and their zones.
Do you replace automatic door sensors in Consett?
Yes. Sensor replacement and upgrades in Consett are booked and managed by us and carried out by engineers who specialise in automatic doors. They work on sensors for sliding, swing, folding and revolving doors from most makers. The visit cost is set in writing before they attend, and each new sensor is tested before they leave.
Are parts quoted before they are fitted?
Always. If a repair or service in Consett needs parts, such as rollers, belts, sensors, a control board or a motor, we quote them in writing first. Some common parts may be on the engineer's van; others are ordered once you accept the quote and fitted on a return visit at a price already agreed.
How is the visit price set for work in Consett?
We agree the visit price with you in writing before an engineer attends. It is based on the type of door, the work requested and the location. If parts or further work are needed once the engineer has found the cause, those are quoted before they are done, so the cost never moves without your agreement.
Who is responsible for automatic doors on escape routes in Consett?
Under the Regulatory Reform (Fire Safety) Order 2005 the responsible person for the premises must make sure escape routes work and fire safety equipment is maintained. Automatic doors on an escape route need fail-safe opening or break-out, set by the fire strategy.