Coverage across Gwynedd
There is no branch to visit in Gwynedd; instead, specialist engineers working under our management travel to you. That keeps drive unit replacement available across the whole area, including smaller towns and rural addresses. The page for each of the 3 towns we list below sets out nearby places, guide prices and the questions people usually ask.
Towns listed in Gwynedd: Bangor, Holyhead, Caernarfon.
What to think about for drive unit replacement in Gwynedd
- Listed buildings and conservation areas in Gwynedd make it attractive to keep the existing frame. A new operator inside the existing header changes little that can be seen.
- If the door is on an escape route, the new drive unit must be set up to open, break out or be openable by hand, as the building's fire strategy requires.
- Worn floor guides and rollers can shorten the life of a new operator. It is often worth replacing them during the same visit rather than coming back later.
- Business parks and office blocks in Gwynedd with several identical doors can replace operators in phases, keeping at least one entrance open at all times.
- Ask for the paperwork. A converted door should come with its risk assessment, Declaration of Conformity and user instructions, which belong with your building and maintenance records.
Drive unit replacement in Gwynedd: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: typically £1,995 to £3,995 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| New drive unit on an existing automatic sliding door | £1,995 – £3,995 | existing leaves kept, installed, ex VAT |
| New operator on an existing automatic swing door | £1,795 – £3,995 | installed, ex VAT |
| Sensors replaced at the same time | £195 – £495 | per sensor, ex VAT |
Standards and rules in Wales
Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible. BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them.
Whoever motorises a manual door, or builds an automatic door from separate parts, may take on the manufacturer’s legal duties for the finished door: a risk assessment, a technical file kept available for the authorities, a Declaration of Conformity, the conformity marking and instructions. You receive the Declaration of Conformity and the instructions at handover. In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking.
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance.
How it works
- Send photos and the address. A few pictures of the door from both sides, the address in Gwynedd and a note of who uses the entrance help us understand the job before anyone visits the site.
- No-cost survey on site. We arrange a survey at a time that suits the building. The engineer records measurements, fixings and power, plus any constraints such as listed status, opening hours or access for deliveries.
- Itemised quote to approve. We price every element of the work on drive unit replacement separately in a written quote that you can check, share and approve. Lead time and payment stages are stated, and nothing is ordered until you accept.
- Fit, test and hand over. On the agreed dates the engineer installs the equipment, commissions the operator and tests each safety function. You get a demonstration, the test record and any conformity paperwork that applies to the work.
Keep the frame, replace the drive. Arrange a free survey in Gwynedd and receive a fixed quote covering the new operator, sensors and paperwork.
Drive unit replacement in Gwynedd: questions
Do you provide paperwork for the converted door in Gwynedd?
Yes. When we fit a new drive unit we prepare the paperwork for the finished door, including the risk assessment, Declaration of Conformity and user instructions, and hand it over with the test results and settings. It belongs with your building records.
How much should I budget for drive unit replacement in Gwynedd?
Our guide is £1,995 to £3,995 excluding VAT (per door), the same guide prices we use across the UK. The free site survey in Gwynedd confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
What lead time should we expect in Gwynedd?
Once the quote is accepted, drive units are typically 2 to 4 weeks to arrive, depending on the length and weight rating needed. The changeover date is agreed with you as soon as the parts are confirmed, and it can be planned around your opening hours.
How long will our entrance in Gwynedd be closed for the changeover?
A standard sliding door changeover typically takes a day, and a swing operator often less. The work can be scheduled early, after closing or at a weekend so it causes less disruption. Your quote shows the planned date and how long the entrance will be out of use.
What happens once the installation in Gwynedd is finished?
The engineer tests every function, including the safety sensors and the behaviour on power loss, and sets the door up with reference to BS EN 16005. You are shown how to use the controls and which simple checks to make, and you receive the handover documents, including the test record and any conformity paperwork that applies to the work.
Will the building stay secure while the entrance is being changed?
We plan to keep the entrance usable or secure throughout. Where a door has to come out, the work is sequenced so the opening is closed up before the engineer leaves, or a temporary door or hoarding is arranged when a longer gap cannot be avoided. How this is handled for your site in Gwynedd is agreed before work starts.
Do businesses in Gwynedd have to fit automatic doors?
There is no blanket requirement. Service providers and employers must make reasonable adjustments for disabled people under the Equality Act 2010, and Welsh building regulations guidance expects entrances that are easy to open. An automatic door is a common way to meet both.