Covering Cirencester and nearby
We do not keep premises in Cirencester. Instead, enquiries about safety and compliance upgrades come to us, we agree the price in writing, and a specialist engineer working under our management travels to the address in the GL7 postcode district on a date that suits the site.
Many buildings in Cirencester are older, with timber frames, thick walls, steps or uneven thresholds. These affect where an operator and sensors can go, and the engineer checks them on site before anything is fitted or adjusted.
Nearby towns we also list for safety and compliance upgrades (straight-line distance): Stroud (10.0 miles), Cheltenham (13.3 miles), Swindon (13.8 miles), Gloucester (15.4 miles), Chippenham (19.1 miles), Calne (19.4 miles).
What to think about for safety and compliance upgrades in Cirencester
- If your building in Cirencester has one main entrance, battery backup lets the door open safely in a power cut, so there is always a way in and out.
- Busy retail and public buildings in Cirencester may prefer upgrade work out of hours. Most single-door upgrades are completed in one visit, so disruption is limited.
- Escape route doors must open, break out or be openable by hand as the fire strategy requires. Check what yours says before choosing which upgrades to make.
- Listed buildings and conservation areas in Cirencester may limit visible changes. Slim sensors and discreet guards keep the look of the historic entrance largely unchanged.
- Programme switches within reach of the public in Cirencester should be key-operated or protected, so the door cannot be left in an unsafe mode by mistake.
Safety and compliance upgrades in Cirencester: guide prices
The site survey is free, including the measured drawing and a fixed, itemised written quote. Guide price: from £195 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Side-screen protection or guarding | from £295 | per door, ex VAT |
| Battery backup for power-cut operation | £395 – £695 | per door, ex VAT |
| Programme switch with key | £145 – £345 | fitted, ex VAT |
| Upgrade package for an older door | £795 – £2,495 | typical, after an inspection, ex VAT |
Standards and rules in England
Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible. BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them.
Whoever motorises a manual door, or builds an automatic door from separate parts, may take on the manufacturer’s legal duties for the finished door: a risk assessment, a technical file kept available for the authorities, a Declaration of Conformity, the conformity marking and instructions. You receive the Declaration of Conformity and the instructions at handover. In Great Britain a new or converted powered door must meet the Supply of Machinery (Safety) Regulations 2008 before it is first used, and can carry the UKCA or the CE marking.
How it works
- Start with a short enquiry. Use the form, phone or email. Tell us whether the work is a new door, an upgrade or an opener for a home, and we arrange the next step for your site in Cirencester.
- Measured survey. The free survey confirms what will fit and what the entrance needs: opening width, door type, activation, safety sensors and behaviour on power loss or fire alarm, matched to how the building is used.
- Written price, no surprises. A fixed, itemised quote sets out the specification, the work involved, the expected lead time and the warranty terms. You can ask questions or change the specification before accepting it.
- Installed and commissioned. The door is installed with as little disruption as possible, then set up and tested for its hazard zones. Before leaving, the engineer explains the controls and hands over the documents for your records.
Send us your inspection report for doors in Cirencester, and we will arrange a free survey and quote each upgrade as a separate item.
Safety and compliance upgrades in Cirencester: questions
Will you document the upgrades on our door in Cirencester?
Yes. You receive a record of what was fitted, the settings and the test results, linked to each finding in the inspection report. Keep it with your service records for insurers, landlords or anyone else who asks how the door's risks have been dealt with.
What will safety and compliance upgrades in Cirencester cost?
Our guide starts from £195 excluding VAT (per door), the same guide price we use across the UK. The free site survey in Cirencester confirms the price as a fixed, itemised written quote, and the guide price tool gives you a range before anyone visits.
Our door in Cirencester has no battery backup. Do we need one?
It depends on whether the door is on an escape route and what the fire strategy for the building requires. Doors on escape routes usually need to open, break out or be openable by hand if the power fails. The person responsible for fire safety in the building should confirm the requirement.
Do you need an inspection before upgrading a door in Cirencester?
Not always. If you know what you need, such as a key switch or new signs, we can survey and quote for it directly. For a full picture of the door's risks, a documented safety inspection is the better starting point, and it is a separate service priced before the visit.
Do you service doors in Cirencester after installing them?
Yes. We recommend a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer's instructions and how heavily the door is used; busy doors are often serviced more often. Servicing can follow on from the installation, with the price agreed in writing and a record left after every visit.
What happens once the installation in Cirencester is finished?
The engineer tests every function, including the safety sensors and the behaviour on power loss, and sets the door up with reference to BS EN 16005. You are shown how to use the controls and which simple checks to make, and you receive the handover documents, including the test record and any conformity paperwork that applies to the work.
Who is responsible for automatic doors on escape routes in Cirencester?
Under the Regulatory Reform (Fire Safety) Order 2005 the responsible person for the premises must make sure escape routes work and fire safety equipment is maintained. Automatic doors on an escape route need fail-safe opening or break-out, set by the fire strategy.