Covering Blairgowrie and nearby
Engineers working under our management travel to addresses across the PH10 postcode district for sensor upgrades and replacement. There is no depot or showroom in Blairgowrie; you arrange everything with us by phone, email or the form on this page, and we confirm the price in writing first.
Many buildings in Blairgowrie are older, with timber frames, thick walls, steps or uneven thresholds. These affect where an operator and sensors can go, and the engineer checks them on site before anything is fitted or adjusted.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Perth (14.0 miles), Dundee (16.3 miles), Forfar (17.5 miles), Cupar (22.6 miles), Crieff (24.3 miles), Carnoustie (25.0 miles).
What to think about for sensor upgrades and replacement in Blairgowrie
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in Blairgowrie so the zones can be set for the new surface.
- Sensor changes on escape route doors must never stop the door opening when it needs to. The engineer checks the door's escape mode after any sensor work.
- After a near miss at a door in Blairgowrie, keep a note of what happened and where the person was standing. It helps the engineer judge which zone the sensor failed to cover.
- Doors with side screens may need a light curtain on the leaf edge or post to protect the gap. This is one of the most common upgrades on older sliding doors.
- Shopping parades and older shopfronts in Blairgowrie sometimes have low transoms or canopies that limit where a sensor can be mounted. The engineer checks height and angle first.
Sensor upgrades and replacement in Blairgowrie: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in Scotland
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Make contact. Phone, email or use the form. Tell us the type of door, what it is doing and whether it is safe to use, so the right visit for sensor upgrades and replacement can be planned.
- Written visit price. The cost of attending is agreed in writing before the visit is booked. For a planned service or inspection, the price per door and what each visit includes are set out at the same time.
- On-site work. The engineer, working under our management, checks the door from end to end, deals with the fault or the service, and tests every safety function and sensor setting before signing the door off.
- Report and quote. You receive a report of the findings. Where a repair, part or upgrade is recommended, it is quoted in writing so you can decide, and the door is left in a safe state if it cannot be used.
For doors that open for passers-by or close too soon in Blairgowrie, talk to us about new sensors and detection zones set for your entrance.
Sensor upgrades and replacement in Blairgowrie: questions
Can you price new sensors for my door in Blairgowrie from photos?
Often, yes. Photos of the sensor, the door from both sides and the label on the operator cover usually tell us which sensor is needed and whether it suits the controller. We can then quote the sensor and fitting in advance, with the visit price confirmed before anyone travels.
What will sensor upgrades and replacement in Blairgowrie cost?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Blairgowrie, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Do engineers carry sensors for doors in Blairgowrie?
Engineers carry common combined and safety sensors, so many replacements can be fitted at the first visit. Light curtains and specialist sensors are ordered once the door is identified, with delivery typically 1 to 2 weeks. Photos in advance help us bring the right part first time.
Do you replace automatic door sensors in Blairgowrie?
Yes. Sensor replacement and upgrades in Blairgowrie are booked and managed by us and carried out by engineers who specialise in automatic doors. They work on sensors for sliding, swing, folding and revolving doors from most makers. The visit cost is set in writing before they attend, and each new sensor is tested before they leave.
What if a door in Blairgowrie is found to be unsafe?
The engineer explains the problem and, where needed, leaves the door in a safe state, for example switched off or set so it cannot trap or strike anyone. You receive a written note of the issue. The repair or upgrade that would put it right is quoted before any further work is carried out.
What happens during a visit in Blairgowrie?
The engineer checks how the door is operating, diagnoses the fault or carries out the service, and tests the safety sensors and other functions before leaving. On a service visit that includes cleaning, adjustment and lubrication where needed. Anything that cannot be put right on the visit, or that needs parts, is explained and quoted before further work goes ahead.
Do businesses in Blairgowrie have to fit automatic doors?
No law requires automatic doors everywhere. Under the Equality Act 2010 service providers and employers must make reasonable adjustments for disabled people, and Scottish guidance says powered doors improve accessibility at entrances. An automatic door is often the practical answer.