Covering Didcot and nearby
Addresses anywhere in the OX11 postcode district can book sensor upgrades and replacement through us. The engineer who attends works under our management and travels to the site. There is no branch in Didcot, so the price, the booking and the paperwork all come from one place.
GP surgeries, dental practices and pharmacies in Didcot often serve older patients and people with limited mobility. A low-energy swing operator, or a gentle sliding door with a push pad, can make a real difference at entrances like these.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Abingdon (4.6 miles), Oxford (9.9 miles), Thatcham (14.2 miles), Newbury (14.8 miles), Reading (15.7 miles), Witney (15.9 miles).
What to think about for sensor upgrades and replacement in Didcot
- Shopping parades and older shopfronts in Didcot sometimes have low transoms or canopies that limit where a sensor can be mounted. The engineer checks height and angle first.
- Rain, snow and blowing leaves can trigger radar sensors over exposed doors. Some sensors filter weather better than others, which the engineer weighs up when choosing a replacement.
- Care settings in Didcot often need longer hold-open times and wider safety zones for residents who move slowly, use walking frames or pause in the doorway.
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
- Sensor changes on escape route doors must never stop the door opening when it needs to. The engineer checks the door's escape mode after any sensor work.
Sensor upgrades and replacement in Didcot: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
How it works
- Make contact. Phone, email or use the form. Tell us the type of door, what it is doing and whether it is safe to use, so the right visit for sensor upgrades and replacement can be planned.
- Written visit price. The cost of attending is agreed in writing before the visit is booked. For a planned service or inspection, the price per door and what each visit includes are set out at the same time.
- On-site work. The engineer, working under our management, checks the door from end to end, deals with the fault or the service, and tests every safety function and sensor setting before signing the door off.
- Report and quote. You receive a report of the findings. Where a repair, part or upgrade is recommended, it is quoted in writing so you can decide, and the door is left in a safe state if it cannot be used.
For doors that open for passers-by or close too soon in Didcot, talk to us about new sensors and detection zones set for your entrance.
Sensor upgrades and replacement in Didcot: questions
Can you price new sensors for my door in Didcot from photos?
Often, yes. Photos of the sensor, the door from both sides and the label on the operator cover usually tell us which sensor is needed and whether it suits the controller. We can then quote the sensor and fitting in advance, with the visit price confirmed before anyone travels.
Is there a guide price for sensor upgrades and replacement in Didcot?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Didcot, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Can you upgrade sensors on an old door in Didcot?
Most older doors can take modern sensors. A few very old controllers cannot monitor current safety sensors. If yours is one of them, we explain whether a controller upgrade or a new drive unit is the better option, and quote it, before any work is done.
Do you replace automatic door sensors in Didcot?
Yes. Sensor replacement and upgrades in Didcot are booked and managed by us and carried out by engineers who specialise in automatic doors. They work on sensors for sliding, swing, folding and revolving doors from most makers. The visit cost is set in writing before they attend, and each new sensor is tested before they leave.
Which makes of automatic door can you work on in Didcot?
Engineers working under our management work on most makes of automatic door, including sliding, swing, folding, telescopic and revolving types. Some older or obsolete operators have limited parts availability. If that applies, we explain the options, which may include a replacement drive unit on the existing frame, and quote them before anything is ordered.
How often should automatic doors in Didcot be serviced?
No law sets a fixed interval. We recommend a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer's instructions and how heavily the door is used; busy doors are often serviced more often. Site staff should also carry out simple regular checks and keep a record of them.
Who is responsible for automatic doors on escape routes in Didcot?
Under the Regulatory Reform (Fire Safety) Order 2005 the responsible person for the premises must make sure escape routes work and fire safety equipment is maintained. Automatic doors on an escape route need fail-safe opening or break-out, set by the fire strategy.