Covering Bicester and nearby
Sites across the OX25, OX26 and OX27 postcode districts are visited by specialist automatic door engineers working under our management. They travel to Bicester for sensor upgrades and replacement as bookings come in, so dates depend on the diary rather than a fixed local team, and we give you the earliest date we can offer when you book.
Many buildings in Bicester are older, with timber frames, thick walls, steps or uneven thresholds. These affect where an operator and sensors can go, and the engineer checks them on site before anything is fitted or adjusted.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Oxford (11.1 miles), Banbury (13.8 miles), Aylesbury (15.6 miles), Witney (16.3 miles), Abingdon (16.8 miles), Bletchley (19.0 miles).
What to think about for sensor upgrades and replacement in Bicester
- Care settings in Bicester often need longer hold-open times and wider safety zones for residents who move slowly, use walking frames or pause in the doorway.
- Shopping parades and older shopfronts in Bicester sometimes have low transoms or canopies that limit where a sensor can be mounted. The engineer checks height and angle first.
- After a near miss at a door in Bicester, keep a note of what happened and where the person was standing. It helps the engineer judge which zone the sensor failed to cover.
- Entrances facing busy roads in Bicester can see false openings from passing vehicles and cyclists. A sensor with direction detection and a tighter zone usually helps.
- Doors with side screens may need a light curtain on the leaf edge or post to protect the gap. This is one of the most common upgrades on older sliding doors.
Sensor upgrades and replacement in Bicester: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
Workplace law (the Workplace (Health, Safety and Welfare) Regulations 1992) expects powered doors to have suitable and effective features to stop them trapping anyone and, where needed for safety, to open by hand unless they open automatically if the power fails. Doors at work must also be kept in efficient working order under a suitable system of maintenance. HSE guidance on those regulations says the frequency of maintenance depends on the equipment and the manufacturer’s information.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Make contact. Phone, email or use the form. Tell us the type of door, what it is doing and whether it is safe to use, so the right visit for sensor upgrades and replacement can be planned.
- Written visit price. The cost of attending is agreed in writing before the visit is booked. For a planned service or inspection, the price per door and what each visit includes are set out at the same time.
- On-site work. The engineer, working under our management, checks the door from end to end, deals with the fault or the service, and tests every safety function and sensor setting before signing the door off.
- Report and quote. You receive a report of the findings. Where a repair, part or upgrade is recommended, it is quoted in writing so you can decide, and the door is left in a safe state if it cannot be used.
Send a photo of the door and sensor at your building in Bicester, and we will confirm the visit price and the likely sensor before booking an engineer.
Sensor upgrades and replacement in Bicester: questions
Can you price new sensors for my door in Bicester from photos?
Often, yes. Photos of the sensor, the door from both sides and the label on the operator cover usually tell us which sensor is needed and whether it suits the controller. We can then quote the sensor and fitting in advance, with the visit price confirmed before anyone travels.
Can you give me a price for sensor upgrades and replacement in Bicester?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Bicester, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Our door in Bicester closes on people. Is that a sensor fault?
It is likely, and the door should be treated as unsafe. Switch it to a safe mode, such as manual or open, and keep people away from the leaves. Tell us it is unsafe and we will give you the earliest visit we can offer, then the engineer will check the safety sensors and their zones.
Will new sensors stop false openings at our entrance in Bicester?
Usually. Modern sensors can ignore cross traffic and detect only people moving towards the door, and the zone can be narrowed. If the entrance faces a busy street or catches heavy weather, the engineer may suggest a sensor that filters those conditions better.
Can you take over servicing of doors in Bicester from another company?
Yes. Send us the door details and, if you have them, previous service records or inspection reports. The first visit gives a baseline for each door, and its price is agreed in writing beforehand. From then on, records continue in one consistent format, whichever company looked after the doors before.
How often should automatic doors in Bicester be serviced?
No law sets a fixed interval. We recommend a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer's instructions and how heavily the door is used; busy doors are often serviced more often. Site staff should also carry out simple regular checks and keep a record of them.
Which building regulations apply to a new automatic entrance in Bicester?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.