Covering St Helens and nearby
If your building is in St Helens, or anywhere in the WA9 and WA10 postcode districts, we can arrange sensor upgrades and replacement. Visits are booked with you in advance, timed around opening hours where that matters, and carried out by engineers who work under our management.
Universities, colleges and city hotels see sharp peaks of traffic at changeover times and check-in hours. For entrances like these in St Helens, opening width, hold-open time and sensor range are set so the door copes with crowds without wasting heat.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Haydock (2.4 miles), Prescot (3.1 miles), Ashton-in-Makerfield (4.1 miles), Huyton (5.1 miles), Newton-le-Willows (5.5 miles), Golborne (5.9 miles).
What to think about for sensor upgrades and replacement in St Helens
- If several doors at one site have the same old sensor, replacing them together keeps the doors behaving consistently and may reduce the cost per sensor.
- Corridor doors that people walk past rather than through may work better on a touch-free switch than a motion sensor, cutting needless openings and heat loss.
- Swing doors in narrow corridors need sensors on the leaf to protect people on both sides. The engineer checks the swing path and any walls or fittings close by.
- Shiny, wet or newly polished floors can confuse infrared safety sensors. Mention any recent floor changes at your building in St Helens so the zones can be set for the new surface.
- Rain, snow and blowing leaves can trigger radar sensors over exposed doors. Some sensors filter weather better than others, which the engineer weighs up when choosing a replacement.
Sensor upgrades and replacement in St Helens: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in England
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Tell us what is happening. Describe the fault, or the service or inspection that is due, and send photos of the door and any label on the operator. Include the address in St Helens and how much the site depends on the door.
- Visit price agreed in writing. We confirm the price of the visit in writing before an engineer attends. If the door can be priced from photos and its make and model, we say so at this stage.
- Engineer visit. A specialist engineer working under our management diagnoses the fault or carries out the service, then tests the operation of the door and its safety sensors before leaving the site.
- Findings and follow-up. You receive a written record of what was found and done. Any parts or further work needed are quoted in writing before they go ahead, and nothing is added without your agreement.
Send a photo of the door and sensor at your building in St Helens, and we will confirm the visit price and the likely sensor before booking an engineer.
Sensor upgrades and replacement in St Helens: questions
Can you upgrade sensors on an old door in St Helens?
Most older doors can take modern sensors. A few very old controllers cannot monitor current safety sensors. If yours is one of them, we explain whether a controller upgrade or a new drive unit is the better option, and quote it, before any work is done.
What do you charge for sensor upgrades and replacement in St Helens?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in St Helens, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Will you record the sensor settings for our building in St Helens?
Yes. The job report lists each sensor fitted, its position, the settings used and the test results. Keep it with your service records, as it helps future engineers and shows the door's safety set-up was checked after the work. The same details are useful if an insurer or inspector asks.
Can a risk assessment in St Helens tell us which sensors we need?
Yes. A safety inspection tests each hazard zone and records where sensor coverage is missing or poor. The report then lists the sensors or light curtains needed, and we can quote those items exactly as listed, or you can pass the report to another competent installer.
What happens during a visit in St Helens?
The engineer checks how the door is operating, diagnoses the fault or carries out the service, and tests the safety sensors and other functions before leaving. On a service visit that includes cleaning, adjustment and lubrication where needed. Anything that cannot be put right on the visit, or that needs parts, is explained and quoted before further work goes ahead.
What should I tell you when reporting a fault in St Helens?
The address, the type of door, what it is doing or not doing, when the problem started and whether it is safe to use. A photo of the operator label showing the make, and a short video of the fault, help a great deal. With that, we can agree the visit price in writing and send an engineer with the right parts where possible.
Which building regulations apply to a new automatic entrance in St Helens?
In England the guidance is Approved Document M (Volume 2) for access, Approved Document B for fire safety and escape routes, and Approved Document K for glazing and powered doors. A new entrance can count as building work, so building control should be involved before it is ordered.