Covering Livingston and nearby
From shops and surgeries to schools, care homes and private houses, any building in the EH53 and EH54 postcode districts can be covered for sensor upgrades and replacement. Specialist engineers working under our management carry out the work, and you deal with us as the contracting party from start to finish.
Town-centre buildings in Livingston range from modern units to older shopfronts. Older frontages can have uneven floors, limited head height and timber frames that need checking before an operator is fitted or adjusted, and the engineer looks at these on site.
Nearby towns we also list for sensor upgrades and replacement (straight-line distance): Broxburn (2.9 miles), Bathgate (4.7 miles), Linlithgow (6.0 miles), Whitburn (6.7 miles), Armadale (7.0 miles), South Queensferry (7.7 miles).
What to think about for sensor upgrades and replacement in Livingston
- After a near miss at a door in Livingston, keep a note of what happened and where the person was standing. It helps the engineer judge which zone the sensor failed to cover.
- Doors with side screens may need a light curtain on the leaf edge or post to protect the gap. This is one of the most common upgrades on older sliding doors.
- Rain, snow and blowing leaves can trigger radar sensors over exposed doors. Some sensors filter weather better than others, which the engineer weighs up when choosing a replacement.
- Sensor changes on escape route doors must never stop the door opening when it needs to. The engineer checks the door's escape mode after any sensor work.
- If several doors at one site have the same old sensor, replacing them together keeps the doors behaving consistently and may reduce the cost per sensor.
Sensor upgrades and replacement in Livingston: guide prices
The visit price is agreed in writing before an engineer attends; parts and any further work are quoted before they are done. Guide price: typically £195 to £495 ex VAT.
| Item | Guide price | Notes |
|---|---|---|
| Add or replace a safety or activation sensor | £195 – £495 | per sensor fitted, ex VAT |
| Touch-free switch or push pad | £145 – £395 | per switch, ex VAT |
| Side-screen or light-curtain protection | from £295 | per door, ex VAT; on survey |
Sensor prices cover the part, fitting and set-up. If a sensor is fitted on a visit of its own, the visit charge (from £95 ex VAT) is added, and we confirm the total in writing before an engineer attends. Each sensor is set up for the door and tested before the engineer leaves.
Standards and rules in Scotland
BS EN 16005 is the current standard for the safety in use of powered pedestrian doors, and BS 7036-0:2014 is the British code of practice for risk assessment and risk reduction used alongside it. Standards are not law in themselves, but they are the recognised benchmark for showing an automatic door is safe to use, and we set up, test and document doors with reference to them. Standards are not retrospective, so an older door does not become unlawful when a standard is updated; a site-specific risk assessment shows whether any upgrades are sensible.
No law sets a fixed service interval. We recommend that a trained engineer checks the safety functions at least once a year, with service intervals set by the manufacturer’s instructions and how heavily the door is used, and that someone on site carries out simple regular checks and keeps a record.
How it works
- Explain the problem. Whether the door is stuck, slow, noisy or due its next check, a short description and a few photos tell us which kind of visit to book for sensor upgrades and replacement and what to bring.
- Visit cost agreed. You get the visit price in writing before we book the engineer. There are no hidden extras: parts and further work are always quoted separately and in advance.
- Engineer on site. The engineer inspects the operator, sensors, tracks and leaves, carries out the repair or service, and runs the door through its safety tests before it goes back into use.
- Follow-up quoted. You are sent a record of the visit. If something else needs attention, we quote it in writing; for doors on a service plan, the next visit date is noted on the record.
Ask for a price on new safety or activation sensors in Livingston. Each one is set up for the door's hazard zones and tested before the engineer leaves.
Sensor upgrades and replacement in Livingston: questions
Do you replace automatic door sensors in Livingston?
Yes. Sensor replacement and upgrades in Livingston are booked and managed by us and carried out by engineers who specialise in automatic doors. They work on sensors for sliding, swing, folding and revolving doors from most makers. The visit cost is set in writing before they attend, and each new sensor is tested before they leave.
What price range should I expect for sensor upgrades and replacement in Livingston?
Our guide is £195 to £495 excluding VAT (per sensor fitted), the same guide prices we use across the UK. We agree the visit price in writing before an engineer attends in Livingston, and quote any parts or further work before doing them. The price guide lists typical repair and service costs.
Will new sensors stop false openings at our entrance in Livingston?
Usually. Modern sensors can ignore cross traffic and detect only people moving towards the door, and the zone can be narrowed. If the entrance faces a busy street or catches heavy weather, the engineer may suggest a sensor that filters those conditions better.
Can you price new sensors for my door in Livingston from photos?
Often, yes. Photos of the sensor, the door from both sides and the label on the operator cover usually tell us which sensor is needed and whether it suits the controller. We can then quote the sensor and fitting in advance, with the visit price confirmed before anyone travels.
What should I tell you when reporting a fault in Livingston?
The address, the type of door, what it is doing or not doing, when the problem started and whether it is safe to use. A photo of the operator label showing the make, and a short video of the fault, help a great deal. With that, we can agree the visit price in writing and send an engineer with the right parts where possible.
Are parts quoted before they are fitted?
Always. If a repair or service in Livingston needs parts, such as rollers, belts, sensors, a control board or a motor, we quote them in writing first. Some common parts may be on the engineer's van; others are ordered once you accept the quote and fitted on a return visit at a price already agreed.
Who is responsible for automatic doors on escape routes in Livingston?
The person responsible for fire safety under the Fire (Scotland) Act 2005 for those premises. Scottish guidance allows automatic doors on escape routes only where they fail safely to outward opening or have a monitored fail-safe system that opens them on power failure, sensor failure and fire alarm.